You put a brisket in the smoker. For a few hours the probe climbs happily. Then it reaches somewhere around 150–170°F (65–77°C) and stops. Ten minutes, then an hour, then three. Nothing is wrong. That is the stall, and it ends by itself.
Why it happens
A big, wet piece of meat is like a person on a warm day: it sweats. Moisture works its way to the surface and evaporates, and evaporating water takes a lot of heat with it. For a stretch, the heat your cooker puts in is almost exactly matched by the heat the surface loses to evaporation, so the temperature barely moves.
(Collagen starting to melt and fat rendering also soak up energy in this range. They add to the pause, but evaporation is the main reason.)
Three things follow:
- It affects big, moist cuts. Brisket, pork shoulder (butt) and large roasts. A rack of ribs or a chicken is too small for much of a stall.
- It lasts as long as the surface stays wet. Once the surface dries and the bark sets, the temperature starts climbing again.
- A humid cooker makes it shorter. Less evaporation, smaller stall. A dry, windy cooker evaporates more and stalls harder.
Why it works
Evaporation is cooling. Water turning to vapor carries heat away from the meat’s surface, so the meat can’t warm until the water supply runs low. Nothing is broken, and no cooker setting is “wrong.” Wrapping or raising the heat simply changes the balance.
Three ways through
1. Wait it out
Leave the meat alone and let it work through. This gives the best bark and the deepest smoke flavor, because the surface stays exposed. The price is time: the stall can last two to five hours on a large cut, and the whole cook may run well past what a recipe guessed.
2. Raise the cooker temperature
Turn the heat up, say from 225–250°F (107–120°C) to 275–300°F (135–150°C). More heat in means it out-muscles evaporation sooner. This saves time and keeps an open, firm bark. The price is a faster cook with less margin: the outside can dry or darken more, and lean sections of the meat can get tougher.
3. Wrap
Wrap the meat tightly once the bark has the color you like, usually when the stall is well underway. Wrapping stops evaporation, so the temperature moves again at once.
- Foil traps everything. Fastest of the options, but the meat braises in its own juices: very moist, and the bark goes soft and the surface a little pot-roasty.
- Butcher paper (unwaxed, food-safe) breathes a bit. Slower than foil, keeps more of the bark’s texture, and lets some steam out.
| Option | Effect on time | Effect on bark |
|---|---|---|
| Wait it out | Longest; hours added | Best: dry, deep, crusty |
| Raise cooker temperature | Noticeably shorter | Good, though it darkens faster |
| Wrap in butcher paper | Shorter; moderate savings | Fairly good, slightly softer |
| Wrap in foil | Shortest | Softest; bark turns wet and tender |
There is no single right answer. Competitions and busy home cooks wrap; purists wait. If you want to sit down to dinner at a set time, wrap or raise the temperature. If you want the crustiest bark and have all day, wait.
Plan a schedule that includes it
Work backward from dinner:
- Choose the serving time. Then add a long rest: 1–2 hours for brisket or shoulder wrapped in a towel inside a dry cooler or a warm oven. Holding is forgiving; that rest is your safety buffer.
- Allow roughly 1½ to 2 hours per pound (3–4 hours per kilo) at 225–250°F (107–120°C) as a rough guess for big cuts, and add extra time to be safe. Ends up early? Hold it. Late? Pull the plug and carve or go to a hotter oven.
- Start earlier than you think. Many cooks put a brisket on overnight so the stall happens while they sleep.
- Cook to tenderness, not a number. Tough cuts are done when a probe slides in with almost no resistance, usually around 195–205°F (90–96°C). This is the collagen turning to gelatin, explained in What You're Cooking: Muscle, Fat & Collagen.
Food safety
These cuts are cooked far beyond the USDA minimums (145°F / 63°C for whole cuts of beef and pork, with a 3-minute rest), so the stall itself is not a safety issue. The cooker is: keep its temperature steady, and don’t leave finished meat sitting between 40°F and 140°F (4–60°C) for more than 2 hours. Hold hot meat above 140°F (60°C), or chill and reheat it. See Cookout Food Safety.
What not to do
- Don’t chase the temperature. Raising the fire in panic, then again, then again, gives you a cooker that swings wildly and dries the meat.
- Don’t keep opening the lid. Every peek lets out heat and humidity, which lengthens the stall and the cook.
- Don’t pull the meat early. A shoulder taken off in the stall is cooked but tough; the collagen hasn’t had its time. Wait until the probe says tender.
- Don’t trust a single spot. Probe the thickest part and at least one more place, not touching bone.
- Don’t wrap too early. Wrapped before the bark sets, the surface turns mushy, because there’s no crust yet.
What it means at the cooker
- Expect the stall. Plan for it and relax.
- Decide before you start: wait, hotter, or wrap.
- If you wrap, do it when the color is right and the surface is firm to the touch.
- Cook to tenderness, then rest.
More on the full cook in Low-and-Slow, Start to Finish, and on what makes the crust in Smoke Rings & Bark.